Intex Motor Mount Kit
| Brand: | Intex | ||
| Average Rating |
|
Boat equipment has been receiving high demands these days. In fact, its market is even growing up to this day. If you want to know more about the different boat equipment that is suitable and compatible for your boats, then you might want to consider looking for additional information regarding your targeted purchase. In that regard, this article will be talking more about the Intex Motor Mount Kit and its features.
The Intex Motor Mount Kit has a lot of features, and one thing that you would particularly like about this is that you do not need any other tools to place it on the boat. It makes use of bolt that has a strong thumb type screws, and you’re done. Aside from that, you can’t go wrong with this fine solid marine plywood. All in all, the Intex Motor Mount Kit is a motor mount that is designed to do for Intex boats. In fact, it holds the small Minn Kota Endura 30 very well. This mount will also accept a 3.5 hp, but if you are on an Excursion boat, you can only put a maximum of 1.5 hp up to 18 pounds of motor weight. If you intend to go through a 3.5, then you would need a Mariner boat or a Sea Hawk Two.
In addition to the features mentioned above, the Intex Motor Mount Kit features a motor mount kit that is designed for inflatable boats of Intex. As a matter of fact, it allows you to attach a maximum of 3.5 horse power motors. Its great design is made up of marine plywood that has an aluminum support arms for maximum strength. It is easy to use, and it attaches and detaches easily. For storage, you can just disassemble it for storage, while for compatibility; it is suitable for almost all the most recent model of Intex boats.
Basically, the Intex Motor Mount Kit will allow you to relax as you cruise down the river with your Intex inflatable boat. This mount will let you rest your arms while you float in comfort. more info
Well made, does what it should
Rating:5 out of 5 stars
One thing I like about this mount, you don’t need any tools to put it on the boat. It uses bolts with sturdy thumb type screws and your done. Also, can’t go wrong with good solid marine plywood. In the end, its a motor mount and it does what it is designed to do for the intex boats. Holds that little Minn Kota Endura 30 really good. The mount can accept a 3.5hp but on the Excursion boats you can only put up to a 1.5hp or up to 18 lbs motor weight. If you want to go to a 3.5 you will need to get a Sea Hawk II or Mariner boat.
Intel Motor Mount Kit
Rating:3 out of 5 stars
I would not recomend the use of an electic trolling motor in this particular water craft.The battery is too cumbersome as well as unstable. These conditions can cause poor contact with the battery conections;therefore frequent motor disruptions. I’m guessing the best motor for the job would be a low horse power gas motor with the gas on the motor as seen in the illustration .
Only one flaw
Rating:5 out of 5 stars
I just received my mount today and I have to admit that its perfect. Easy to set up. But only one flaw, there is a real strong odor or maple or pine. Other then that it is a well built mount. Will let every one know later if it fits a Inflatable Challenger 3 with a 40 thrust motor in a comment on this review some time next week.
Perfect!
Rating:5 out of 5 stars
This motor mount is just what the doctor ordered. Thanks for a great product and speedy delivery too!
acceptable but not ideal
Rating:3 out of 5 stars
eh the thing works but it seems my trolling motor sinks deep down into the water when trying to run at 4 or 5 which with a raft to get anywhere you need..
Muy aceptable!
Rating:4 out of 5 stars
De buena construcción, sin embargo por el precio esperaba que la montura fuese menos básica.
Soporta muy bien las 30 lbs de mi motor eléctrico.
Just one flaw.
Rating:3 out of 5 stars
Mine just arrived today, when I put it together I noticed that the holes in the wooden board that the motor attaches to are a little bigger than the washers provided. If you try to tighten the nuts the washers sink down into the board therefore not serving their purpose. I had to go to the hardware store to get bigger washers to fit. May be just mine but just thought you should know before you take it out. You may have to get bigger washers….I got a set of regular washers. Overall it serves its purpose and with $0.30 worth of washers it works fine.